Journal Paper

1. "Enhanced desalination performance of an electrodialysis stack in over-limiting current by adding AC/Fe3O4 nanocomposite as a flow electrode"
   Zohreh Akbari Jonoush, Mohammad Ali Mostafaei
   Journal of Water Process Engineering, Vol. 61, pp.105304-105317, 2024
2. "Optimizing weld strength and microstructure in CP-titanium and 304 stainless steel friction welds with chromium interlayer"
   Mohammad mostafa Sheykhi, Mohammad Ali Mostafaei
   Results in Materials, Vol. 24, pp.100627-100640, 2024
3. "A novel approach to investigate the effect of friction stir welding parameters on hardness and grain size of pure titanium using artificial Neural Network"
   Navid Siamakmanesh, Mohammad Ali Mostafaei
   Materials Today Communications, Vol. 38, pp.108404-108409, 2024
4. "Pre and post rolling homogenization of direct chill cast Al-6Mg alloy: Effect on microstructure and mechanical properties"
   Mohammad Ali Mostafaei, Mohsen Kazeminezhad
   Advances in Materials and Processing Technologies, Vol. 1, pp.1-1, 2023
5. "Application of a Novel Process Called Vacuum-Encapsulated Slurry Method to Form a Silicide-Aluminide Protective Coating on Ti6Al4V Alloy"
   Saeed Nouri, Mohammad Ali Mostafaei, Masoud Asayesh
   JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE, Vol. 31, pp.9504-9509, 2022
6. "Bimodal grain size and mechanical properties enhancement in low carbon steel by ultra-rapid annealing"
   Mohammad Ali Mostafaei, Mohsen Kazeminezhad
   Journal of Materials Research and Technology-JMR and T, Vol. 18, pp.2363-2367, 2022
7. "Improvement of ?' coarsening model in high ?' volume fraction Ni-base superalloys containing different Ta/W ratio"
   M. Mostafaei, S.M. Abbasi, Mohammad Ali Mostafaei
   JOURNAL OF ALLOYS AND COMPOUNDS, Vol. 885, 2021
8. "Serrated yielding behavior after cold and hot rolling of a high Mg content Al-Mg alloy"
   Mohammad Ali Mostafaei
   JOURNAL OF ALLOYS AND COMPOUNDS, Vol. 811, 2019
9. "Grain-refining ability of ultra-rapid annealing for low-carbon steel severe plastic deformation"
   Mohammad Ali Mostafaei, Mohsen Kazeminezhad
   Materiali in Tehnologije, Vol. 51, pp.173-177, 2017
10. "Effect of Starting Microstructure through Severe Plastic Deformation and Ultra-Rapid Annealing of Low-Carbon Steel"
    Mohammad Ali Mostafaei, Mohsen Kazeminezhad
    STEEL RESEARCH INTERNATIONAL, Vol. 87, pp.1527-1533, 2016
11. "Microstructural evolution during ultra-rapid annealing of severely deformed low-carbon steel strain temperature and heating rate effects"
    Mohammad Ali Mostafaei, mohsen kazeminezhad
    International Journal of Minerals Metallurgy and Materials, Vol. 23, pp.779-792, 2016
12. "Microstructure and mechanical properties improvement by ultra-rapid annealing of severely deformed low-carbon steel"
    Mohammad Ali Mostafaei, mohsen khazeminezhad
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, Vol. 655, pp.229-236, 2016
13. "Study on microstructure and mechanical characteristics of low-carbon steel and ferritic stainless steel joints"
    Mahmoud Sarkari Khorrami, Mohammad Ali Mostafaei, hesam pouraliakbar, Amir Hossein Kokabi
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, Vol. 608, pp.35-45, 2014
14. "Analyses on the Flow Stress of an Al-Mg Alloy During Dynamic Recovery"
    Mohammad Ali Mostafaei, M. Kazeminezhad
    JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE, Vol. 22, pp.700-705, 2013
15. "A novel approach to find the kinetics of dynamic recovery based on hot flow curves"
    Mohammad Ali Mostafaei, M. Kazeminezhad
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, Vol. 544, pp.88-91, 2012
16. "Hot deformation behavior of hot extruded Al6Mg alloy"
    Mohammad Ali Mostafaei, M. Kazeminezhad
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, Vol. 535, pp.216-221, 2012
17. "The effect of temperature on microstructure during ultra-rapid annealing of severely deformed low-carbon steel"
    Mohammad Ali Mostafaei, Mohsen Kazeminezhad
    Vol. 10, pp.1-12, 2020

Conference Paper

1. "Friction welded joint of CP-titanium to 304 stainless steel with Cr interlayer"
   Mohammad mostafa Sheykhi, Mohammad Ali Mostafaei
   , 2023
2. "Reuse of thermosetting polymer matrix composites reinforced with glass fibers as filler in epoxy flooring"
   Fatemeh Heidari, Mohammad Ali Mostafaei, Asal Hosseini Monazzah
   , 2022
3. "The effect of fiber type and sample geometry on the compressive strength of engineered cementitious composites"
   Porya Parvizi, Asal Hosseini Monazzah, Mohammad Ali Mostafaei
   , pp.1-8, 2022